@article { author = {Sharghi, Y. and Alinia, F. and Siahkoohi, H. R.}, title = {Detecting Potential Seepage Paths in Bakhtyari Dam Site using Seismic Tomography}, journal = {Scientific Quarterly Journal of Geosciences}, volume = {19}, number = {76}, pages = {71-78}, year = {2010}, publisher = {Geological Survey of Iran}, issn = {1023-7429}, eissn = {2645-4963}, doi = {10.22071/gsj.2010.55649}, abstract = {Seismic travel time tomography uses seismic waves to image velocity distribution inside the ground. This method has been widely applied to practical applications in many fields including earth sciences. In this method, first-arrival times of seismic waves due to artificial sources, observed at receivers in the vicinity of the exploration target are analyzed to obtain the velocity distribution within the propagation area. This paper describes the seismic tomography investigation performed at the abutments of Bakhtyari Dam site. The study aimed to find the low-velocity zones that may correspond to jointed media where seepage most likely happens. We performed 3-D tomographic inversion on Bakhtiari dam seismic data. To perform ray tracing and travel-time computation at each iteration, we used Um and Thurber (1987) method and for inversion step we used SIRT method. In most of the tomograms, average velocity was 3km/s. According to the Barton relation (2006) the seepage potential in dam sit abutments, is low. A low velocity zone has been detected above the 690 m level in right abutment. It shows that the weak zones extended from surface down to this level. Despite the presence of some weak zones, the rock mass quality is good, and the design of the grout curtain could help to bypass the reservoir water away from these seepage paths}, keywords = {Seismic Tomography,Tomogram,Dam,Seepage,Seismic,Inversion,lugeon,Seepage Potential}, title_fa = {استفاده از روش توموگرافی لرزهای برای تعیین پتانسیل نشت از تکیه‌گاه‌های سد بختیاری}, abstract_fa = {توموگرافی از زمان اولین رسید برای ارایه تصویری از ساختار سرعتی زیر زمین از امواج لرزه‌ای استفاده می‌کند. این روش به‌طور وسیع در علوم‌زمین و زمین‌شناسی مهندسی به‌کار می‌رود. زمان سیر امواج حاصل از چشمه لرزه‌ای که توسط گیرنده‌ها دریافت می‌شوند، برای مطالعه محدوده بین چشمه و گیرنده‌ها به‌کار می‌رود. این نوشتار، برداشت‌های توموگرافی انجام یافته در ساختگاه سد بختیاری را مورد بررسی قرار می‌دهد. هدف این بررسی، پیدا کردن زون‌های کم‌سرعتی است که منطبق با بخش‌های درزه‌دار با پتانسیل نشت در  جناحین ساختگاه است. برای تجزیه و تحلیل داده‌های برداشت شده در سد بختیاری، تحلیل توموگرافی سه بعدی انجام شده است. توانایی تحلیل سه بعدی برای مقابله با مسئله عدم یکتایی جواب در داده‌های توموگرافی، یک برتری بسیار بالا  به‌شمار می‌رود برای ردیابی پرتو و محاسبه زمان رسید در هر تکرار، از روش ارائه شده توسط  Um & Thurber (1987)استفاده شده و عملیات وارون با استفاده از تکنیک SIRT صورت گرفته است. در این مطالعه، میانگین سرعت در بیشتر مقاطعی که برداشت توموگرافی در آنها انجام شده در حدود km/s 3 به‌دست آمده است. با استناد به رابطهBarton (2006) می‌توان گفت که نفوذپذیری تکیه‌گاه‌های سد، در مجموع پایین است. در جناح راست و در افق‌های بالاتر از 690 متری، یک زون کم‌سرعت دیده می‌شود که نشان‌دهنده گسترش زون‌های ضعیف موجود در سطح تا این ژرفا است. با وجود حضور زون‌های ضعیف در برخی از توموگرام‌ها، کیفت توده سنگ ساختگاه در مجموع خوب است و با طراحی پرده آب‌بند مناسب می‌توان از نشت آب از این زون‌‌ها جلوگیری کرد.}, keywords_fa = {توموگرافی لرزه‌ای,توموگرام,سد,نشت,لرزهنگاری,وارون‌سازی,لوژن,نفوذپذیری}, url = {http://www.gsjournal.ir/article_55649.html}, eprint = {http://www.gsjournal.ir/article_55649_fe1581e7892a0984f28eaed3b4901b30.pdf} }