References
Akun, M. E. & Karpuz, C., 2005- Drillability studies of surface-set diamond drilling in Zonguldak region sandstones from Turkey, International Journal of Rock Mechanics and Mining Science, 42, 473-479.
Bruland, A., 1998- Hard rock tunnel boring-drillability test methods. Department of building and construction engineering, NTUN university, Norway..
Drake, R., 2004-Bench drilling techniques and equipment selection manual, Ingersol-Rand Company.
Ersoy, A. & Waller, M. D., 1995a- Textural characterization of rocks. J. of Engineering Geology, June, VoL. 39, Issues 3-4, 123-136.
Ersoy, A. & Waller, M. D., 1995b- Prediction of drill-bit performance using multi-variable linear regression analysis. Transactions of the Institution of Mining and Metallurgy, Section A: Mining Industry, , Vol. 104, May-August, pp. A101-114.
Hoseinie, S. H. & Ataei, M., 2007- A review of machine parameters influencing the drilling rate in mines, 7th International Scientific Conference on Modern Management of Mine Producing and Environmental Protection (SGEM2007), Albena Complex, Bulgaria.
Hoseinie, S. H., Pourrahimian, Y. & Aghababaei, H., 2006- Analyzing and physical modeling of joints dipping effects on penetration rate of rotary drilling in open pit mines, 15th International Symposium on Mine Planning and Equipment Selection (MPES2006)., Torino, Italy. 1007-1013.
Hoseinie, S. H., Aghababaei, H. & Pourrahimian, Y., 2008- Development of a new classification system for assessing of Rock mass Drillability index (RDi), International Journal of Rock Mechanics and Mining Science, 45, 1-10.
Hugh, W. E., 1987- Handbook of Surface Mining, Society of Mining Engineering.
Jimeno, C. L., Jimeno, E. L. & Carcedo, F. J. A., 1995- Drilling and blasting of rocks. A.A Balkema, Pub Rotterdam,
Jung, S. J., Prisbrey, K. & Wu, G., 1994- Prediction of rock hardness and drillability using acoustic emission signatures during indentation. International Journal of Rock Mechanics and Mining Science, Vol. 31, Issue 5, 561-567.
Kahraman, S., 1999- Rotary and percussive drilling prediction using regression analysis. International Journal of Rock Mechanics and Mining Science, , 36: 981-989
Kahraman, S., Balci, C., Yazici, S. & Bilgin, N., 2000- Prediction of the penetration rate of rotary blast hole drilling using a new drillability index. International Journal of Rock Mechanics and Mining Science, 37: 729-743.
Kaiser, P. K. & McCreath, D. R., 1994- Rock mechanics considerations for drilled or bored excavations in hard rock. Tunneling and Underground Space Technology, Vol. 9, Issue 4, October, 425-437.
Li, X., Rupert, G., Summers, D. A., Santi, P. & Liu, D., 2000- Analysis of impact hammer rebound to estimate rock drillability, Journal of Rock Mechanics &. Rock Engineering, 33(1), 1-13.
Ozturk, A. C., Nasuf, A. & Bilgin, N., 2004- The assessment of rock cutability and physical and mechanical rock properties from a texture coefficient, Journal of south African Institut of Mining and Metalorgy, August.
Plinninger, R., Spaun, G. & Thuro, K., 2002- Predicting tool wear in drill and blast, Tunnels & Tunnelling International Magazine, April.
Rao, K. U. M. & Misra, B., 1998- Principles of rock drilling, Balkema, Rotterdam..
Serradj, T., 1996- Method of assessment of rock drillability incorporating the Protodyakonov index. Transactions of the Institution of Mining and Metallurgy, Section A: Mining Industry, Vol. 105, Septemser-December, A175-A179.
Singh, S. P., 1990- Rock drillability comparison by different methods. In: Proceedings 2nd Int. Symposium on Mine Planning and Equipment Selection, Calgary, 3-4 November, A.A Balkema, Pub Rotterdam,
Singh, S. P., 1998- Ladouceur. M & Rouhi. F. Sources, implication and control of blasthole deviation. 7th International Symposium on Mine Planning and Equipment Selection. A.A Balkema, Pub Rotterdam.
Singh, T. N., Gupta, A. R., & Sain, R., 2006- A comparative analysis of cognitive system for the prediction of drillability of rocks and wear factor. Geotechnical and Geological Engineering, 24: 299-312.
Tanaino, A. S., 2005- Rock classification by drillability. Part 1: Analysis of the available classification. Journal of Mining Science, Vol. 41, No. 6, pp. 541-549.
Thuro, K., 1997- Drillability prediction- geological influences in hard rack drill and blast tunneling. Geol Runsch, 86: 426-438.
Thuro, K., Spaun, G., 1996- Introducing the destruction work as a new rock property of toughness referring to drillability in convetional drill and blast tunneling, Eurock 96, Turin, Italy,.
Wijk, G., 1991- Rotary drilling prediction. International Journal of Rock Mechanics and Mining Science,Vol. 28, Issue 1, Jan, 35-42.
Wilbur, L., 1982- Rock Tunnel Engineering Handbook. Edited by BickeL and kuesel, Publication of Van Norstrand Reinhold Compan
)